Visit our new site www.tcscrawlers.com for products not listed here and lower prices! |
||
Thunder Tech Racing Clodbuster Diff Lock Kit (Pair) |
||
 |
$44.98 IN STOCK |
Kit includes parts to lock the front and rear axle (two diffs). This kit uses the stock Clodbuster differential gear (not included) and is removable without damage to the stock gears. High quality injection molded parts with needed hardware included. |
RC4WD R2 Black Crawler Transmission |
||
 |
IN STOCK
|
What's included:
|
RC4WD R2 Crawler Transmission |
||
 |
$79.99 IN STOCK |
What's included:
|
Traxxas Stampede Half Shaft Set (2 each) #1951 |
||
 |
$5.79 IN STOCK |
Use these to make custom long driveshafts for most TLT trucks that use the stampede transmission like the SW2, XRC, Scale Chassis, etc. |
Traxxas Jato Half Shaft Set (2 each) #5550 |
||
 |
$7.69 IN STOCK |
Use these to make custom long driveshafts for most TLT trucks that use the stampede transmission like the SW2, XRC, Scale Chassis, etc. |
Traxxas Steel Drive Yoke Set (2 each) #4628X |
||
 |
$17.99 IN STOCK |
Use these yokes on the axle side of your driveshafts. Plastic yokes don't stand up to the abuse of the rocks. When using these you must either remove the C-clip from the output of the axle or grind down the small ring on the steel yoke so you have enough bite on the output of the axle. |
Traxxas Plastic Drive Yoke Set (2 each) #4628 |
||
 |
$3.89 IN STOCK |
Use these yokes on the transmission side of your driveshafts. |
JB Weld |
||
 |
$5.99 IN STOCK |
Use to lock axle and tranny differentials. |
Traxxas Stampede Transmission Parts |
||
 |
 |
We sell all the components for the Traxxas Stampede Tranny here. |
Clodbuster Clear Plastic Gear Cover (2 Each - One Pair) |
||
 |
$6.99 IN STOCK |
High quality clear plastic gear covers for the Tamiya Clodbuster axle housing. |
5x11x4 Rubber Shielded Bearing |
||
 |
$0.99 IN STOCK |
Use for the Stampede Tranny which needs 6 each bearings. Or for TLT axles which require 20 each.
|
Stampede Transmission Rubber Shielded Bearing Kit (6 pieces) |
||
|
$5.94 IN STOCK |
Includes 6 each 5x11x4 bearings, enough for one Stampede Transmission.
|
TLT Rubber Shielded Bearing Kit (20 piece) for two TLT axles |
||
|
$19.80 IN STOCK |
Includes 20 each 5x11x4 bearings, enough for one set of TLT axles (2 axles)
|
Clodbuster Rubber Shield Bearing Kit (20 piece) |
||
|
$19.99 IN STOCK |
Includes four 5x8x2.5 bearings and sixteen 6x12x4 bearings, enough for one pair of axles (2 axles). All bearings have rubber shields.
|
Thunder Tech Adjustable Motor Mounts - Clodbuster (pair) |
||
 |
$29.98 IN STOCK |
Set of two Thunder Tech Racing Adjustable Motor Mounts for the Tamiya Clodbuster. Allows the use of 6 tooth to 16 tooth pinions with no modifications to the stock Tamiya Clodbuster axle. Also includes two clear adhesive dust covers. |
RcGuy Adjustable Motor Mounts - Clodbuster (pair) |
||
 |
$29.99 IN STOCK |
Set of two RcGuy Adjustable Motor Mounts for the Tamiya Clodbuster. Allows the use of 8 tooth to 14 tooth pinions with no modifications to the stock Tamiya Clodbuster axle. Also includes two clear plastic dust covers. |
Complete Unassembled Clodbuster Axles (pair) |
||
 |
$139.99 IN STOCK |
Set of two new complete unassembled Clodbuster axles. Includes everything shown and internals (gears, etc.). Assembly required. Assembly instructions included. |
TTR/MIP Clodbuster CVD's (one pair for one axle) |
||
 |
$44.98 IN STOCK |
|
RcGuy 8 tooth 32 pitch Pinion Gear for Clodbuster |
||
 |
$9.99 IN STOCK |
These help lower the gearing for rock crawling. These have a heavy duty steel ring and a hex head set screw. Includes one each pinion gear. Please use thread locker on the sets screws when installing these pinion gears. |
Robinson Racing Pinion Gear, 12 tooth, 48 Pitch |
||
| |
$3.69 IN STOCK |
|
Robinson Racing Pinion Gear, 13 tooth, 48 Pitch |
||
 |
$3.69 IN STOCK |
|
Robinson Racing Pinion Gear, 14 tooth, 48 Pitch |
||
| |
$3.69 IN STOCK |
|
Robinson Racing Pinion Gear, 15 tooth, 48 Pitch |
||
| |
$3.69 IN STOCK |
|
SP-FSH03 - Use with Clod to Max Adapters and CVD's |
||
 |
$3 IN STOCK |
This kit contains a set of four (4) 10-32 X 1 " Flanged Serrated Head bolts for use when mounting Thunder Tech Racing Wheel Widener (CLD2MX - Clod to Maxx adapters) ONLY onto the Clodbuster CVD's. If mounting Clod to Maxx adapters and 14-23mm adapters onto CVD's use SP-FSH04. |
SP-FSH04 - Use with Clod to Max Adapters with 14-23mm Adapters and CVD's |
||
| |
$3 IN STOCK |
This kit contains a set of four (4) 10-32 X 1 1/4 " Flanged Serrated Head bolts for use when mounting Thunder Tech Racing Wheel Widener (CLD2MX - Clod to Maxx adapters) WITH 14-23mm adpaters onto the Clodbuster CVD's. |
SP-ST01 Spacer Tube set for DEL-CB03 |
||
 |
$2 IN STOCK |
This kit contains four (4) Alum. Spacer Tubes that are needed when mounting the MAXX to Clod Wheel Adaptor kit #DEL-CB03 (CLD2MX) onto any of our MIP Axle kits (Clodbuster CVD's, etc). |