Visit our new site www.tcscrawlers.com for products not listed here and lower prices! |
||
Complete TQ3 System with Rear Steer Installed |
||
 |
$65 IN STOCK |
New Traxxas TQ3 transmitter, receiver and crystal set with the rear steering kit already installed. A complete Ready-To-Run radio system for rock crawlers with four wheel independent steering. |
TQ3 Rear Steering Kit |
||
 |
$9 IN STOCK |
Convert your TQ3 to operate the rear steering of your crawler. Rear steering significantly improves crawling performance. Detailed instructions with photos and a three position spring return switch are included. Disassembly of your TQ3 and soldering are required. |
Integy Lathe Motor 45 Turn Single Wind |
||
 |
$18.99 IN STOCK |
|
Integy Lathe Motor 55 Turn Single Wind |
||
| |
$18.99 OUT OF STOCK |
|
Integy Lathe Motor 65 Turn Single Wind |
||
| This latest batch has an orange can! Photo will be up soon | $18.99 OUT OF STOCK |
|
Castle Creations Mamba Max Electronic Speed Control (ESC) |
||
 |
$135.99 OUT OF STOCK |
Brushless and Brushed motor speed control. This speed controller has a drag brake that is vital for great down hill performance.
|
Castle Creation s Mamba 25 Electronic Speed Control (ESC) |
||
 |
$75.99 IN STOCK |
Brushless motor speed control commonly used on both TLT and Clodbuster based rigs. |
Castle Creations Castle Link USB Interface Adapter |
||
 |
$20.99 OUT OF STOCK |
Use this adapter to program your mamba 25 and other Castle Creations speed controls. Compatible with Windows 98SE, 98ME, 2000, and XP. USB port required. |
Tekin Rebel 2 Electronic Speed Control (ESC) |
||
 |
$79.99 OUT OF STOCK |
One of the most commonly used ESC's for rock crawling. Use on both dual motor clodbuster trucks and the smaller 2.2 TLT-1 trucks. Caution! You must use a voltage regulator with this esc if you are going to run it with two robot servos or two ultra torque servos. (part #ACC234) click here. |
Hitec 5995TG Robot Servo - Ultra High Torque |
||
 |
$114.99 IN STOCK |
333 oz/in of torque @ 6 volts makes this one of the most powerful servos for the larger scale rock crawlers. 180 degrees of rotation is useful to help pre-load the servo saver. Best if used with a radio that has End Point Adjustment (EPA) to adjust the travel of the servo. The best choice for a competition super class (16" wheelbase) rig. If using two of these, you should add a voltage regulator to your system (part #ACC234) here. See the tutorial bellow on how to wire in your voltage regulator. Some custom tech info here. |
Hitec 5955TG Robot Servo - Ultra High Torque |
||
 |
$114.99 IN STOCK |
333 oz/in of torque @ 6 volts makes this one of the most powerful servos for the larger scale rock crawlers. 90 degrees of rotation allows you to drop this servo in and not worry about limiting the 180 degrees like the 5995TG servo. Aluminum heat-sink case. If using two of these, you should add a voltage regulator to your system (part #ACC234) here. See the tutorial bellow on how to wire in your voltage regulator. Some custom tech info here. |
Airtronics 94359Z Ultra High Torque |
||
 |
$139.99 IN STOCK |
200 oz/in of torque @ 6 volts. Metal heat sink case. 90 degrees of rotation means you don't need to use End Point Adjustments. Just drop this in your crawler for tons of steering power. If using two of these, you should add a voltage regulator to your system (part #ACC234) here. |
Hitec 5645MG |
||
|
$54.99 IN STOCK |
164.2 oz/in of torque at 6 volts. 90 degrees of travel. Still a good servo for larger scale trucks but ideal for 2.2 smaller scaled vehicles. |
Hitec 645mg |
||
|
$39.99 IN STOCK |
133 oz/in of torque at 6 volts. 90 degrees of rotation. Good for small 2.2 scale vehicles. |
12" Servo Extension |
||
$4.49 IN STOCK |
||
Tutorial - Wiring up a voltage regulator for high torque servo systems |
||
|
You want to use a voltage regulator anytime you have two servos that draw allot of power. The robot servos together probably draw 5 amps or more when at full power. This is too much for the tekin rebel 2 and other esc's, so you need something to help with the power requirements of the servos. You only use one voltage regulator. The "male" end of the regulator will plug directly into the battery port of your receiver. The other end wires directly into the battery connector on the esc. The cleanest way to do this is to wire a male servo lead to the battery connector, then just plug the female end of the voltage regulator into the lead on the battery connector.
|
|
SMC 3600 mAh 6 Cell Battery Pack |
||
 |
$34.99 OUT OF STOCK |
|
The StickTM and Tracer Battery Pack |
||
| Deans:
Tamiya:
|
$25 TAMIYA - IN STOCK DEANS - IN STOCK |
This is the custom battery pack needed for the StickTM chassis kit and also works well on the Tracer. This is an 8 cell 1500mAh battery pack. Choose from either Deans connectors or Tamiya connectors. Length 2.7", height 1.3", width 1.9" |
"The Stick" Battery Hold Down Straps |
||
 |
$2.50/strap OUT OF STOCK |
Fits perfectly around "The Stick" battery plate and battery. Also the perfect size to wrap around standard sub-c battery packs. Perfect for competition to avoid batteries coming loose which will incur penalty points. |
Duratrax Piranha AC/DC Digital Peak Charger NiMh/NiCd |
||
|
$49.99 IN STOCK |
  |
Tamiya Connector Set |
||
 |
$3.89 OUT OF STOCK |
One each female and male connector pre-wired. |
Deans Wet Noodle 12 Gauge Motor Wire RED - per foot |
||
 |
$1.50/foot IN STOCK |
|
Deans Wet Noodle 12 Gauge Motor Wire BLACK - per foot |
||
 |
$1.50/foot IN STOCK |
|
Deans Ultra Plugs - One Pair |
||
 |
$3.09 IN STOCK |
|
Deans Ultra Plugs - Female Ultra Plug, Two Pack |
||
 |
$2.69 IN STOCK |
|
Deans Ultra Plugs - Male Ultra Plug, Two Pack |
||
 |
$3.59 IN STOCK |
|
